Ei Engineering is a fully integrated residential engineering firm with a unique combination of in-house services that provides a one-stop full service company. We believe that a successful project is the out come of maintaining a good relationship with the client and providing services that exceed their expectations.
Services
ENERGY MODELING

Energy Modeling services for single-family, multi-family, custom homes, and light commercial projects.
MECHANICAL ENGINEERING

Manuals J, D, & S calculations; energy modeling IECC and T24 Compliance; HVAC plans depicting venting, ductwork and diffuser placements.
ELECTRICAL ENGINEERING

Electrical Load Calculations; Panel Schedules; Single Line Diagrams; Power and Receptacle plans; Lighting plans; Photometrics.
PLUMBING ENGINEERING

Our engineered plans contain: Waste & Vent design; Water & Gas design; isometrics.
SITE ELECTRICAL

We offer site electrical planning for a variety of commercial and residential projects
MARKETING REPORTS

We offer marketing report services including HERS Scores and Utility Comparisons
Systems Approach
Our MEP Engineering services provides you with an informed and controlled project process over your HVAC, Electrical, and Plumbing installers. With our services, you acquire a sense of control, identifying the desired outcome of your projects, allowing you to competitively bid your projects, and the assurance you receive a lateral comparison between the varying bids. Through our engineering process, you begin to curve the trend of poor workmanship, shown in the adjacent figure, into positive results, by identifying standards, expectations, and identifying installation items of non-conformance. This helps alleviate non-constructible items and eliminates complaints by your consumers.
1. STANDARDS DEVELOPMENT
Ei Engineering’s Design Team creates a set of plans in place, with enforceable standards, which the contractor will be able follow for each development. These plans not only provide the contractor a building block to construct from, but also presents a measurable expectations the contractors need to adhere to, which protects you, as our client, from negative comments and complaints from the consumer.
2. DESIGN
We provide our clients with a full gamut of MEP services to ensure success for their projects. This is accomplished by bringing Ei Engineering in early on in the process, where our team makes sure the architectural and design components are completed accurately and meet all current code requirements.
3. PLAN SUBMITTAL
Our staff becomes thoroughly familiar with all codes, standards, and requirements at the beginning of each project. What this does is lay the foundation for a successful development approval process, while ensuring that the client and consultants project intent are being met. It also provides for builder plans that are accurate, can be used for construction in the field, and are constructible.
4. MEP COMMISSIONING
Through Ei Engineering’s commissioning process, we align our engineering design with the sub trade installation during the first phase of construction. This allows future phases to have quality installation, perform to the proper standards, and achieve customer satisfaction of the homes’ performance.
5. ANALYTICAL REPORTING
Through Ei Engineering’s commissioning process, we align our engineering design with the sub trade installation during the first phase of construction. This allows future phases to have quality installation, perform to the proper standards, and achieve customer satisfaction of the homes’ performance.
Data Driven Solutions
1. REGIONAL REPORT
This is a high-level perspective on how your projects compare to each other on various metrics, focusing on quality, productivity, and cost.
2. ISSUE REPORT
This report provides a deep insight into the nucleus of our analytical data set, involving the performance of each observation item. This report identifies all initial issues observed prior to construction.
3. PLAN SUBMITTAL
Our staff becomes thoroughly familiar with all codes, standards, and requirements at the beginning of each project. What this does is lay the foundation for a successful development approval process, while ensuring that the client and consultants project intent are being met. It also provides for builder plans that are accurate, can be used for construction in the field, and are constructible.
4. MEP COMMISSIONING
Through Ei Engineering’s commissioning process, we align our engineering design with the sub trade installation during the first phase of construction. This allows future phases to have quality installation, perform to the proper standards, and achieve customer satisfaction of the homes’ performance.
5. ANALYTICAL REPORTING
Through Ei Engineering’s commissioning process, we align our engineering design with the sub trade installation during the first phase of construction. This allows future phases to have quality installation, perform to the proper standards, and achieve customer satisfaction of the homes’ performance.
State License Matrix

LICENSED IN MEP
- Arizona
- California
- Colorado
- Nevada
- Texas
- Utah
LICENSED IN MP ONLY
- Oregon
- Washington